If the picture is ready in my eyes than it is ready. I love it to do something which is lots of fun. Entretien avec Manfred Baumann Nature, people, animals … everything is inspiration. At the age of 10 years I got my first camera Praktika from my grandfather. Devenir contributeur Soumettre une info — Contact.
|Country:||Bosnia & Herzegovina|
|Published (Last):||23 May 2009|
|PDF File Size:||11.35 Mb|
|ePub File Size:||9.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Remember me Forgot password? B Limit value Ref. Camshaft timing — belt tightening entrdtien fastening. If the calculated value is less than At this point with lever 1 of fig. When re-fitting introduce the the new pre-combustion lombarrini into the cylinder head so that the side hole of the pre-combustion chamber aligns with the glow-plug hole.
Leave room for the fuel to expand. Tighten then the locknut. Tighten the nuts at the prescribed torque of 25 Nm. The same locations are given on the crankcase. When rifitting tighten the screws at a torque of 10 Nm.
Vandlgard allows outside spindle to disengage from Camshaft Timing — Belt Tightening Tool Reference mark 1 on the crankshaft timing pulley and reference mark 2 on the oil pump housing are timing marks. Do not check it before the engine has lombaedini down and, also in that case, open the radiator cap or expansion tank plug with caution.
Coolant Circulation Pump, Components In order to make the measuring point perpendicular with the bore axis of the cyl- inder Replace sealing rings 3 and 4. When reassembling the exhaust manifold, check that the inside is properly clean and free from lombardihi or breaks. Explain the main result of this experiment and what physics you learned.
That is, dimensions are presented in millimeters mmtorque is presented in Newton-meters Nmweight is presented in kilograms Kgvolume is presented in liters or cubic centimeters cc and pressure is presented in barometric units bar.
The whole surface of the cylinder affected by contact with the piston rings must be rendered with the plateau method. In this case proceed as follows: When refitting tighten the screw fosc a torque of 80 Nm. European Automobile Manufacturers Association Tables shown on fcs page are of useful reference when buying a kind of oil.
Remove the piston rings and clean the slot. Every Hours — Alle Stunden Adjust the belt tension so that a N force at the midpoint of the belt center as shown results in a mm deflection. In the case of manual start-ups, make sure that the relative actions can take place without the risk of hitting walls or dangerous lombqrdini, also considering the movements made by the operator. The A value relates to figure Its function is that of limiting the vacuum whenever it tends to increase.
Start the engine and keep it idle at minimum speed for some minutes. Fuel diesel will start to flow out from coupling 2. Inject lubricating oil no more than 2 cm3 into the intake ducts. TOP Related.
Documents et livres connexes
Bagul Wear protective gloves to avoid touching used oil. It is important to wear the personal safety devices prescribed by work safety laws and also by the standards of this manual. Table of contents General Service Notes Make sure that the oil and the coolant are up to the maximum level. Push rod A to the kombardini and keep it in this position; see figure. Maintenance — Recommended Oil Type — Refilling When re-fitting introduce the the new pre-combustion chamber into the cylinder head so that the side hole of the pre-combustion chamber aligns with the glow-plug hole.
FOCS ENTRETIEN PDF
Remember me Forgot password? B Limit value Ref. Camshaft timing — belt tightening entrdtien fastening. If the calculated value is less than At this point with lever 1 of fig. When re-fitting introduce the the new pre-combustion lombarrini into the cylinder head so that the side hole of the pre-combustion chamber aligns with the glow-plug hole. Leave room for the fuel to expand. Tighten then the locknut.
Kit entretien ligier moteur focs origine